Specifikationer for Yamaha TF 1 digitalmixer

Outline

Fader Configuration 16 + 1 (Master)
Mixing Capacity Input Channels 40 (32 mono + 2 stereo + 2 return)
Aux Buses 20 (8 mono + 6 stereo)
Stereo Buses 1
Sub Buses 1
Input channel functions 8 DCA-grupper
I/O Inputs 16 mic/line (XLR/TRS combo) + 2 stereo line (phono)
Outputs 16 (XLR)
Expansion slots 1
On-board processors DSP 8 effekter + 10 GEQ
USB 34x34 USB Audio Interface, 2-spors indspilning til USB-stick

General specifications

Sampling frequency rate Internal 48 kHz
Signal delay Mindre end 2.6 ms, INPUT til OMNI OUT, Fs=48 kHz
Fader 100 mm motoriserede, opløsning = 10-bit, +10 dB to –138 dB, –∞ dB alle fadere
Total harmonic distortion Mindre end 0.05% 20 Hz–20 kHz @+4 dBu ind i 600 ohm, INPUT til OMNI OUT, Input Gain=Min. (Målt med et –18 dB/oktav filter@80 kHz)
Frequency response +0.5, –1.5 dB 20 Hz–20 kHz, ved +4 dBu output @1kHz, INPUT til OMNI OUT
Dynamic range 110 dB typ., DA-konverter, 107 dB typ., INPUT til OMNI OUT, Input Gain=Min.
Hum & noise level Equivalent input noise –128 dBu typ., Input Gain=Max. (Målt med A-vægtningsfilter)
Residual output noise –85 dBu, ST master off (Målt med A-vægtningsfilter)
Crosstalk –100 dB (Målt med et –30 dB/oktav filter@22 kHz), fortløbende INPUT/OMNI OUT-kanaler, Input Gain=Min.
Power requirements 100–240 V 50/60 Hz
Power consumption 100 W
Dimensions W 510 mm (20.1in)
H 225 mm (8.9in)
D 599 mm (23.6in)

Yamaha TF1 Generelle specifikationer

Nettovægt 13.5 kg (29.8lb)

General specifications

Accessories Quick Guide, Strømkabel, CUBASE AI download information
Options Rack-mount Kit RK5014, udvidelseskort, Fodpedal (FC5)
Others Arbejdstemperatur: 0–40 °C, Opbevaringtemperatur: -20–60 °C

Analog input characteristics

Input Terminals GAIN Load
Impedance
For Use With
Nominal
Input Level Connector balanced /
Unbalanced
Sensitivity*1 Nominal Max. before clip
INPUT1-16 +66dB 7.5KΩ 50-600Ω Mics
or 600Ω Lines
-82dBu (61.6V) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2
or TRS phone *3)
Balanced
-6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
ST IN 1,2 10kΩ 600Ω Lines -30dBV (31.6V) -10dBV (316mV) +10dBV (3.16V) RCA Pin Jack Unbalanced

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*In these specifications, 0dBu = 0.775Vrms.
*+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Analog output characteristics

Output Terminals Source
Impedance
For Use With
Nominal
GAIN SW Output Level Connector balanced /
Unbalanced
Nominal Max. before clip
OMNI OUT 1-16 75Ω 600Ω Lines “+24dBu” position (default)
 
+4dBu (1.23 V) +24dBu (12.3 V) XLR-3-32 type *1 Balanced
PHONES *3 100Ω 40Ω Phones 3mW 75mW Stereo Phone Jack (TRS) *2 Unbalanced

*1.1: GND,2: HOT, 3: COLD 
*2 Tip: LEFT, Ring: RIGHT, Sleeve: GND 
*3 The position of the level control is lowered by 16dB from the maximum.
*In these specifications, 0dBu = 0.775Vrms. 
*All output DA converters are 24bit, 128times oversampling.

Digital input/output specifications

Terminals Format Data length Audio Connector
USB (TO HOST) USB 24bit 34ch input / 34ch output, PCM USB (B type)
iPad USB Playback: MP3 or WAV file data / Record: WAV file data USB (A type)

 

Control I/O specifications

Terminals Format Level Connector
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
FOOT SW TS Phone

 


Yamaha TF1 Digital Mixer

10 anmeldelser

23.209 kr.

Prismatch
Bestillingsvare: Leveringstid 5-8 arbejdsdage
Afhent på lager 0,-
GLS - Pakkeshop 0,-
GLS - Erhvervslevering 59,-
GLS - Hjemmelevering 99,-
Danske Fragtmænd 299,-

Læs mere om levering

Gratis fragt (op til 20 kg) 
  • Kompakt og transportabel
  • Rack-montérbar
  • Yamaha TF1 mixeren leverer alt hvad du skal bruge til mindre systemer


Specifikationer for Yamaha TF 1 digitalmixer

Outline

Fader Configuration 16 + 1 (Master)
Mixing Capacity Input Channels 40 (32 mono + 2 stereo + 2 return)
Aux Buses 20 (8 mono + 6 stereo)
Stereo Buses 1
Sub Buses 1
Input channel functions 8 DCA-grupper
I/O Inputs 16 mic/line (XLR/TRS combo) + 2 stereo line (phono)
Outputs 16 (XLR)
Expansion slots 1
On-board processors DSP 8 effekter + 10 GEQ
USB 34x34 USB Audio Interface, 2-spors indspilning til USB-stick

General specifications

Sampling frequency rate Internal 48 kHz
Signal delay Mindre end 2.6 ms, INPUT til OMNI OUT, Fs=48 kHz
Fader 100 mm motoriserede, opløsning = 10-bit, +10 dB to –138 dB, –∞ dB alle fadere
Total harmonic distortion Mindre end 0.05% 20 Hz–20 kHz @+4 dBu ind i 600 ohm, INPUT til OMNI OUT, Input Gain=Min. (Målt med et –18 dB/oktav filter@80 kHz)
Frequency response +0.5, –1.5 dB 20 Hz–20 kHz, ved +4 dBu output @1kHz, INPUT til OMNI OUT
Dynamic range 110 dB typ., DA-konverter, 107 dB typ., INPUT til OMNI OUT, Input Gain=Min.
Hum & noise level Equivalent input noise –128 dBu typ., Input Gain=Max. (Målt med A-vægtningsfilter)
Residual output noise –85 dBu, ST master off (Målt med A-vægtningsfilter)
Crosstalk –100 dB (Målt med et –30 dB/oktav filter@22 kHz), fortløbende INPUT/OMNI OUT-kanaler, Input Gain=Min.
Power requirements 100–240 V 50/60 Hz
Power consumption 100 W
Dimensions W 510 mm (20.1in)
H 225 mm (8.9in)
D 599 mm (23.6in)

Yamaha TF1 Generelle specifikationer

Nettovægt 13.5 kg (29.8lb)

General specifications

Accessories Quick Guide, Strømkabel, CUBASE AI download information
Options Rack-mount Kit RK5014, udvidelseskort, Fodpedal (FC5)
Others Arbejdstemperatur: 0–40 °C, Opbevaringtemperatur: -20–60 °C

Analog input characteristics

Input Terminals GAIN Load
Impedance
For Use With
Nominal
Input Level Connector balanced /
Unbalanced
Sensitivity*1 Nominal Max. before clip
INPUT1-16 +66dB 7.5KΩ 50-600Ω Mics
or 600Ω Lines
-82dBu (61.6V) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2
or TRS phone *3)
Balanced
-6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
ST IN 1,2 10kΩ 600Ω Lines -30dBV (31.6V) -10dBV (316mV) +10dBV (3.16V) RCA Pin Jack Unbalanced

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*In these specifications, 0dBu = 0.775Vrms.
*+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Analog output characteristics

Output Terminals Source
Impedance
For Use With
Nominal
GAIN SW Output Level Connector balanced /
Unbalanced
Nominal Max. before clip
OMNI OUT 1-16 75Ω 600Ω Lines “+24dBu” position (default)
 
+4dBu (1.23 V) +24dBu (12.3 V) XLR-3-32 type *1 Balanced
PHONES *3 100Ω 40Ω Phones 3mW 75mW Stereo Phone Jack (TRS) *2 Unbalanced

*1.1: GND,2: HOT, 3: COLD 
*2 Tip: LEFT, Ring: RIGHT, Sleeve: GND 
*3 The position of the level control is lowered by 16dB from the maximum.
*In these specifications, 0dBu = 0.775Vrms. 
*All output DA converters are 24bit, 128times oversampling.

Digital input/output specifications

Terminals Format Data length Audio Connector
USB (TO HOST) USB 24bit 34ch input / 34ch output, PCM USB (B type)
iPad USB Playback: MP3 or WAV file data / Record: WAV file data USB (A type)

 

Control I/O specifications

Terminals Format Level Connector
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
FOOT SW TS Phone

 



Varenr.: YAM-TF1
EAN: 4957812560382
Vægt 14

Specifications of Yamaha TF 1 Digital Mixer

Outline

Fader Configuration 16 + 1 (Master)
Mixing Capacity Input Channels 40 (32 mono + 2 stereo + 2 return)
Aux Buses 20 (8 mono + 6 stereo)
Stereo Buses 1
Sub Buses 1
Input channel functions 8 DCA groups
I/O Inputs 16 mic/line (XLR/TRS combo) + 2 stereo line (phono)
Outputs 16 (XLR)
Expansion slots 1
On-board processors DSP 8 effects + 10 GEQ
USB 34x34 USB Audio Interface, 2-track recording to USB stick

General specifications

Sampling frequency rate Internal 48 kHz
Signal delay Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz
Fader 100 mm motorized, resolution = 10-bit, +10 dB to -138 dB, - dB all faders
Total harmonic distortion Less than 0.05% 20 Hz-20 kHz @+4 dBu into 600 ohms, INPUT to OMNI OUT, Input Gain=Min. (Measured with a -18 dB/octave filter@80 kHz)
Frequency response +0.5, -1.5 dB 20 Hz-20 kHz, at +4 dBu output @1kHz, INPUT to OMNI OUT
Dynamic range 110 dB typ., DA-converter, 107 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Hum & noise level Equivalent input noise -128 dBu typ., Input Gain=Max. (Measured with A-weighting filter)
Residual output noise -85 dBu, ST master off (Measured with A-weighting filter)
Crosstalk -100 dB (Measured with a -30 dB/octave filter@22 kHz), consecutive INPUT/OMNI OUT channels, Input Gain=Min.
Power requirements 100-240 V 50/60 Hz
Power consumption 100 W
Dimensions W 510 mm (20.1in)
H 225 mm (8.9in)
D 599 mm (23.6in)

Yamaha TF1 General Specifications

Net weight 13.5 kg (29.8lb)

General specifications

Accessories Quick Guide, Power cable, CUBASE AI download information
Options Rack-mount Kit RK5014, Expansion board, Foot pedal (FC5)
Others Operating temperature: 0-40 °C, Storage temperature: -20-60 °C

Analog input characteristics

Input Terminals GAIN Load
Impedance
For Use With
Nominal
Input Level Connector balanced /
Unbalanced
Sensitivity*1 Nominal Max. before clip
INPUT1-16 +66dB 7.5K 50-600 Mics
or 600 Lines
-82dBu (61.6 V) -62dBu (0.616mV) -42dBu (6.16mV) Combo Jack (XLR-3-31 type *2
or TRS phone *3)
Balanced
-6dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
ST IN 1,2 - 10k 600 Lines -30dBV (31.6 V) -10dBV (316mV) +10dBV (3.16V) RCA Pin Jack Unbalanced

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*In these specifications, 0dBu = 0.775Vrms.
*+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Analog output characteristics

Output Terminals Source
Impedance
For Use With
Nominal
GAIN SW Output Level Connector balanced /
Unbalanced
Nominal Max. before clip
OMNI OUT 1-16 75 600 Lines "+24dBu" position (default)
 
+4dBu (1.23 V) +24dBu (12.3 V) XLR-3-32 type *1 Balanced
PHONES *3 100 40 Phones - 3mW 75mW Stereo Phone Jack (TRS) *2 Unbalanced

*1.1: GND,2: HOT, 3: COLD 
*2 Tip: LEFT, Ring: RIGHT, Sleeve: GND 
*3 The position of the level control is lowered by 16dB from the maximum.
*In these specifications, 0dBu = 0.775Vrms. 
*All output DA converters are 24bit, 128times oversampling.

Digital input/output specifications

Terminals Format Data length Audio Connector
USB (TO HOST) USB 24bit 34ch input / 34ch output, PCM USB (B type)
iPad USB - Playback: MP3 or WAV file data / Record: WAV file data USB (A type)

 

Control I/O specifications

Terminals Format Level Connector
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
FOOT SW - - TS Phone

 



/upload_dir/templates/DC2024_oktober